Your Plumbing Crash Course: What You Must Have for Bathtub Installation
Your Plumbing Crash Course: What You Must Have for Bathtub Installation
Blog Article
Just how do you actually feel on the subject of How to Install a Bathtub Yourself?
Mounting a bath tub isn't exactly rocket science, however it does need strong plumbing, woodworking, and sometimes, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately challenging project. If the old bathtub is easily easily accessible, the job can move rapidly; if you have to open a wall surface to eliminate the old tub as well as place the brand-new bathtub, the task is much harder. In either instance, the project is within a home handyman's skills, although you will certainly require an assistant to vacate the old bathtub and set in the new one. Make certain you have actually certified on your own for the work as well as fit attempting it. Rather than hiring a specialist to take over a halfway-completed task, it is far better to think about employing one before you begin. Chances are you may require a specialist plumber to make tube links.
This short article will certainly help you mount a new bathtub in your shower room if you have currently purchased a brand-new bathtub and also don't require to alter the arrangement of your previous water pipelines.
Your devices and material checklist should make up the following:
Planning for the Installation
First of all, the sustaining structure provided with the bath must be fitted (if required) according to the supplier's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets device to avoid strain on the bathtub.
Fit the flexible tap adapters to the bottom of the two faucets using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you use all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its last position.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, then the first thing you must do is separate the supply of water. After doing so, activate the faucets to drain pipes any water staying in the system. The procedure of getting rid of the existing faucets can be rather problematic due to the limited gain access to that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the taps. Have a towel all set for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have been gotten rid of, use the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from transforming throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing compound.
Prior to moving on to fit the brand-new faucets, contrast the pipe links on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Setting up the Bathtub
Utilizing both wooden boards under its feet, place the bath tub in the needed setting. The wood boards are valuable in equally spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four little factors.
The following objective is to make sure that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also readjusting the feet on the bath tub up until the level checks out level.
To install faucets, fit the bottom of the outermost adaptable faucet adapter to the proper supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
Activate the supply of water and also check all joints and brand-new pipework for leakages and tighten them if essential. Fill the bath tub as well as also check the overflow electrical outlet and also the normal electrical outlet for leaks.
Ultimately, deal with the bath paneling as described in the manufacturer's user's manual. Tiling and also sealing around the bath tub ought to wait up until the bathtub has actually been made use of at least when as this will settle it right into its final placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will require a plastic connector to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the mounting opening in the bath/basin making certain that the washing machines are in place in between the tap as well as the sink. Safeguard the faucet in place with the manufacturer given backnut. Once the faucet is firmly in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical tap connectors. The previous kind should be connected to the tap finishes initially, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bathroom meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to crack a stiff seal, triggering the water to pass through the wall surface between the bath as well as the tiling, leading to problems with moisture and also feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealers to assimilate your components as well as fittings. They are offered in tubes and cartridges, and can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Bear in mind to always load the tub with water before securing, to permit the activity experienced when the bathtub remains in use. The sealer can crack rather early if you do not consider this movement prior to securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently available on the marketplace. It is advisable to fit the floor tiles making use of waterproof or water resistant glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Post a remark further down. We'd be interested to hear your opinion about this write up. In hopes that you come back again later on. Liked our posting? Please share it. Let others discover it. Many thanks for your time. Visit again soon.
Secure fix? Ring! Report this page